CMI floor & energy . riscaldamento . raffrescamento . energie rinnovabili dal sole      
 
ITALIANO FLOOR & ENERGY REALIZZAZIONI SERVIZI OPPORTUNITA' & CARRIERA LINKS NEWS ED EVENTI CONTATTI
RADIANT . pannelli radianti CLIMAHOUSE . riscaldamento e raffrescamento PHOTOVOLTAIC . energie rinnovabili dal sole AREA TECNICA . progettazione e normative
print




  ON-LINE CATALOGS
BROWSE OUR CATALOGS
 
The FLOOR HEATING LINE is composed of five different solutions of thicknesses and thermal inertia, allowing the best use of the available space for installation in accordance with the regulations.

THE RANGE

-BASIC 100 size 100 mm
-BASIC 85 size 85 mm
-BASIC MINI 55 size 55 m
-BASIC MINI 30 R size 30 mm
-BASIC MINI 30 DRY size 30 mm


PANNEL BASIC 100
The pannel of the line BASIC 100 has a thickness of 60 mm composed of:
 - insulating base 30 mm
 - studs 30 mm

The studs have a wheelbase of 75 mm which allows for the installation wheelbase following:
 - 75 mm
 - 150 mm
 - 225 mm
 - 300 mm

Ensuring correct installation of the facility, a perfect installing and curvature of the pipe without crushing the tube.

The tube used with this panel has a 17 mm diameter and the screed to superimpose a thickness of 40 mm.

The BASIC 100 is recommended for floors where the bottom is cold and for all the buildings with sufficient space to accommodate its thickness.

SPECIAL FEATURE 
- Covered in a blue thin film of polyethylene, whose function is to be a barrier to the vapor

- Dimensions 1350 x 750mm

- basic 30 mm to prevent heat loss down

- studs of 30 mm for a perfect installation of the tube, allowing the placement of it under the studs floor  and protecting during installation phase and work

- 4 teeth by 4 mm, corresponding to each stud to take away the tube from the plan, an important feature to optimize heat exchange and  the performance of the installation; in this way the screed fits perfectly to the pipe, projecting heat produced by the plant to the up

- 2 cuttings male and 2 female along the four sides to facilitate the fitting during the assembling and to avoid creating cracks and so thermal bridges.



PANNEL BASIC 85
The pannel of the line BASIC 85 has a thickness of 45 mm composed of:
 - insulating base 15 mm
 - studs 30 mm

The studs have a wheelbase of 75 mm which allows for the installation wheelbase following:
 - 75 mm
 - 150 mm
 - 225 mm
 - 300 mm

Ensuring a correct system’s execution, a perfect installing and the right curvature of the pipe without crushing the tube.

The tube used with this panel has a diameter of 17 mm and the screed to superimpose a thickness of 40 mm.

SPECIAL FEATURE 
- Covered in a blue thin film of polyethylene, whose function is to be a barrier to the vapor

- Dimensions 1350 x 750mm

- basic 30 mm to prevent heat loss down

- studs of 30 mm for a perfect installation of the tube, allowing the placement of it under the studs floor  and protecting during installation phase and work

- 4 teeth by 4 mm, corresponding to each stud to take away the tube from the plan

- 2 cuttings male and 2 female along the four sides to facilitate the fitting during the assembling and to avoid creating cracks and so thermal bridges.
 


PANNEAU BASIC MINI 55
The pannel of the line BASIC MINI 55 has a thickness  of 30 mm composed of :
 - insulating base 15 mm
 - studs 15 mm

The studs have a wheelbase of 30 mm which allows the installation wheelbase following:
 - 60 mm
 - 90 mm
 - 120 mm
 - 150 mm
 - 180 mm
 - 210 mm

The tube used with this panel has a diameter of 12 mm and the screed to superimpose a thickness of 25 mm.

BASIC MINI 55 is recommended for environments with little thermal inertia, for restructuring of many buildings especially old buildings, for environments in which we must make the least possible weight on the slab.

SPECIAL FEATURE
- Covered in a blue thin film of polyethylene, whose function is to be a barrier to the vapor

- Dimensions 1350 x 750mm

- basic 15 mm to prevent heat loss down

- studs of 15 mm for a perfect installation of the tube

- 4 teeth by 3 mm, corresponding to each stud  

- 2 cuttings male and 2 female along the four sides to facilitate the fitting during the assembling and to avoid creating cracks and so thermal bridges.


 
PANEL MINI 30 R
The pannel of the line BASIC MINI 30R has a thickness of 30 mm composed of:
 - insulating base 15 mm
 - studs 15 mm
The studs have a wheelbase of 30 mm which allows for the installation wheelbase following:
 - 60 mm
 - 90 mm
 - 120 mm
 - 150 mm
 - 180 mm
 - 210 mm
The tube used with this panel has a diameter of 12 mm.

BASIC MINI 30R is recommended:
- for floors where the bottom is warned up
- for environments with little thermal inertia, 
- in restructuring, 
- for cases where it is necessary to use a very low discharge temperature 25-28 °

SPECIAL FEATURE
- Covered in a blue thin film of polyethylene, whose function is to be a barrier to the vapor and the humidity

- Dimensions 1350 x 750mm

- basic 15 mm to prevent heat loss down

- studs of 15 mm for a perfect installation of the tube

- 4 teeth by 3 mm, corresponding to each stud  

- 2 cuttings male and 2 female along the four sides to facilitate the fitting during the assembling and to avoid creating cracks and so thermal bridges.

- The use of less material to achieve the screed 
less screed = less weight on the floor

- Thanks to a filler screed, the installation will be only 30 mm, the drying time of only 4 days. This screed is made of innovative material under study by CMI in collaboration with a leading company in producing products for the building.

PANEL BASIC 30 DRY
The pannel of the line BASIC MINI DRY 30 has a thickness of 27 mm composed of :
 - insulating base 14 mm
 - studs 13 mm
The studs have a wheelbase of 75 mm which allows for the installation wheelbase following :
 - 75 mm
 - 150 mm

The tube used with this panel has a diameter of  14 mm. 

The BASIC MINI DRY 30 is recommended:
- for floors where the bottom is warned up
- environments with little thermal inertia (the installation should quickly reach the required temperature)
- in restructuring of old buildings
- For installations of loft

SPECIAL FEATURE 
- dimensions 1.350 x 750 mm
- basic 14 mm 
- studs of 13 mm for a perfect installation of the tube 
- 2 cuttings male and 2 female along the four 
- The dry system provides no screed on the installation. It consists in a panel only 27mm, in which shaping have been obtained, so that it can accommodate small strips of sheet metal adapted to contain the tube of diameter 14 mm.
 
Special slides of spreading in galvanized steel 0.3 mm are made with regular break points for an easier installation and to transmit the temperature to 2 sheets stacked and glued to ensure the support from the floor and spread the thermal energy homogeneously
 
A big advantage of the system  BASIC MINI DRY 30 is the possibility to warm the atmosphere with very low discharge temperatures, 25-28 ° in some cases, reducing consumption.
   
 









  •      
     
         
       
    C.M.I. srl - heating, cooling, renewable energy from the sun
    Legal and Operational seat: C.so Novara , 219 d/e - 27029 Vigevano (Pv) - Telephone: 0381/326750 - Fax: 0381/326751
    E-mail: cmifloor@cmifloor.it - Skype: CmiFloorEnergy
     
    Copyright © 2011 Studio G&G Corporate Communication